Flightgear joystick rudder factor power9/23/2023 ![]() It looks likeĪn RC 4 channel transmitter but with no guts. Made specifically for the free FMS simulator. My joystick device was a "TR Flight Simulator" No. ![]() Now the throttle stick movement can be reserved at will.īoth the nasal and non-nasal methods have worked. These values are the same for an aircraft (C172p) or the helicopter (B0-105). setting = 1): Throttle: 0.00000įor throttle lever pushed (Internal Properties /. In (the sim.) Help > Joystick Information, I read:įor throttle lever pulled (Internal Properties /. Setting = -1 for full throttle lever (pushed, full for an aircraft, mini collective for descend for the helicopter). Setting = (a value close to zero) at the middle Setting = 1 with throttle lever at zero (pulled, idle for an aircraft, full collective for climbing for the helicopter) Just try it If this does work for you, lean back and be happy You can see what FlightGear has detected your joystick as in the Help > Joystick Configuration dialog from the menu. Script = 'controls.throttleAxis()' (unspecified) FlightGear has integrated joystick support, which automatically detects any joystick, yoke, or pedals attached. If it can help for your calibration, with my joystick, I read (in the Internal Properties /input/ joysyicks/js/axis[2)/binding My throttle binding is only this (common for aircrafts and helicopters, but with the rule above): Equally, “full power” has the thrust controller at idle Therefore for minimum collective you have to push the control down (that is the full acceleration position (!) of the thrust controller). Then in controls/flight you can read the values FG is getting for X/Y and twist.To increase the rotor thrust, you have to “pull” the collective. Look at input/ joystick to see what driver Xml file its using. Replacing the original file.Īdd default into the start of the xml as in this clip below.Īlso check what FG is getting the internal properties up. As it was a quick and nasty but it seemed to work ok.Ĭopy the distro Force 3D pro file to be input/joystick/default/joystick.xml. However I threw the windows version 1.9 on an xp machine with one for a test hack the other day. My scripts would not be much help as I only use X/Y and the hat switch for the autopilot. I have been using them for a while with out problems for the last 3 releases. The values return by both programs for both axis seem reasonable.Įdit: added info about my installation. ![]() I have no idea what might be causing this issue.īoth js_demo and jstest recognize the throttle and the rudder axis without problem. I tried reducing the factor from 1.0 to 0.9 but the only change was that the value approached 0.9 instead of 1.0 and then I got the erratic values again. This happens if I turn the stick right or left. ![]() It occurred timely at low speed, enabling plane to travel full length of runway. During inputs by either keystroke or stick twist, response of rudder to control input appeared fixed. If I turn it a little more, even nearer of the end of the turn I get erratic values. frank galloney - Multiple ground tests were performed, while observing a conventional geared aircraft from above. I also tried setting a offset but the throttle axis is always ignored by fgfs AFAICT.Ībout the second issue: a little explanation first: the value received by fgfs, as per, Help->Joystick Information, starts from zero (at the centre) to 1 near the end on the stick turn. I tried removing the nasal script and setting as a property-value but I'm not sure I used the proper property name. I say this because the throttle axis is the only one using a nasal script and is the only one not responding at all. rudder has erratic behaviour at full stick turnįor the first issue I believe the nasal script used to manage the throttle axis might be the one to blame. Right now I'm dealing with to main issues:Ģ. By now the only modifications are the names recognized but I want to fix all issues on it. I'm using a modified wingman force 3d xml file. Just trying to configure my joystick on my first FlightGear installation. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |